My Cart Checkout Speak to an expert! Call us on 0151 236 7800 0151 236 7800
Neutrik XIRIUM PRO TX Analog line input module - Mains Power Only Permanent Install Version (NXP-TM-ANA-E-PI)

Neutrik XIRIUM PRO TX Analog line input module - Mains Power Only Permanent Install Version (NXP-TM-ANA-E-PI)

£169.50 (inc. vat)
£141.25 (ex. vat)

Brand: Neutrik

Usually Ships in 1 - 3 Days

The Neutrik Xirium Pro NXP-TM-ANA-E-PI is the permanent installation version of the NXP-TM-ANA-E, this PI version does not feature battery power and must be mains powered.

The Neutrik XIRIUM PRO NXP-TM-ANA-E-PI is an Analog Line Input Module for the XIRIUM PRO Europe Transmitter TX (NXP2TX-E).

Interested in hiring this product?
Send an enquiry now.
Add this item to your Wishlist.
OR
Description

Neutrik XIRIUM PRO TX Analog line input module - Mains Power Only Permanent Install Version (NXP-TM-ANA-E-PI)

The Neutrik Xirium Pro NXP-TM-ANA-E-PI is the permanent installation version of the NXP-TM-ANA-E, this PI version does not feature battery power and must be mains powered.

The Neutrik XIRIUM PRO NXP-TM-ANA-E-PI is an Analog Line Input Module for the XIRIUM PRO Europe Transmitter TX (NXP2TX-E).

Input and output module options handle common signal type
Whether the signal type is analog, digital (AES/EBU) or Dante, XIRIUM PRO offers modules to accept any of them. Signal types may also be converted from one type to another, simply by selecting the appropriate module. Need to transmit an analog signal and plug into a digital input? No problem. Select an analog input module for the transmitter, and the AES digital output module for the receiver. In fact, every receiver in a system can use a different output module, allowing for signal conversion to the type used by your device.

Specifications

SPECIFICATIONS

GENERAL SPECIFICATIONS

  • Radio frequency carrier range: IEEE 802.11a, UNII-3 band from 5725 MHz to 5825 MHz (channels 149-165), license-free
  • Data protocol: Proprietary (DiWA technology)
  • Transmit power: Conducted 8 dBm / 14 dBm (with 6 dBi antenna)
  • Range: Up to 500 m point to point (LOS), longer range depending on obstacles, reflexions, interferences, XROC mode

AUDIO PERFORMANCE (ANALOG TO ANALOG PER WIRELESS LINK)

  • THD + Noise (TX Gain = min.): < 0.01 % @ 1 kHz, 4 dBu / < 0.05 % @ 20 Hz – 10 kHz, 4 dBu
  • Frequency response: +0.5 dB / -1.5 dB @ 20 Hz – 20 kHz ref. 1 kHz
  • Dynamic range: > 105 dB @ 1 kHz, A-weighted
  • Crosstalk: < -80 dB @ 20 kHz
  • Number of audio channels @ 24 mbps: 2
  • Number of audio channels @ 6 mbps: 1 (XROC mode)
  • Number of receivers: Unlimited number of RX clients
  • Converter resolution (ADC & DAC): 24 bit
  • Sampling rate: 48 kHz
  • Latency (Delay): 3.6 msec (analog to analog)
  • Transmission method: Compression-free, no reduction of converted data
  • Operating temperature: 32° F to +122° F / 0 °C to +50 °C
  • Storage temperature: -4° F to +176° F / -20 °C to +80 °C

TX SPECIFIC CHARACTERISTICS

  • Antenna 5-6GHz - Audio Transmission: Omni-directional, 6 dBi, 25° Elevation and 360° Azimuth, N-connector male (direct mount)
  • Antenna 2.4GHz - Control Data Transm.: 1/2 wave dipole with SMA female connectors
  • Number of audio channels: 2
  • Number of audio channels @ 6mbps: 1 (XROC mode)

ADDITIONAL DIGITAL AUDIO INTERFACES

  • AES/EBU: 24 bit / 48 kHz according to AES3-2003
  • Dante AoE (Audio over Ethernet): proprietary protocol by Audinate®

ANALOG INPUT SPECS

  • Input Type - Line Balanced
    • Input Level
    • Input Imp.: 10 kOhm
    • Rated Source Imp.: 1000 Ohm
    • Max.*: 22 dBU (* maximum input level before signal overflow, 0 dBu = 0.775 V rms)
    • Connector type: XLR

OTHER

  • Indicators: LEDs: Power ON / Start Up / Low Battery Status / XROC mode / Linking Process / Audio transmission
  • Controls: Power ON / Linking Process / XROC mode
  • Power Supply: NXP-TM-ANA-E-PI: Mains input over powerCON TRUE1 (100-240 VAC 50/60 Hz)
Additional Information

Additional Information

Manufacturer Neutrik
SKU RNEUNXPTMANAEPI
Model NXP-TM-ANA-E-PI
GTIN NA
Single or Pair N/A