Currency:
T: 0151 707 4545

Retro Instruments 2A3 Dual Channel Tube Program Equalizer based on the Pultec 1A3

£4,236.00 £3,530.00 (ex. vat)




Retro Instruments 2A3 Dual Channel Tube Program Equalizer based on the Pultec 1A3

  • Retro Instruments 2A3 Dual Channel Tube Program Equalizer based on the Pultec 1A3
  • Retro Instruments 2A3 Dual Channel Tube Program Equalizer based on the Pultec 1A3
  • Retro Instruments 2A3 Dual Channel Tube Program Equalizer based on the Pultec 1A3

Retro Instruments 2A3 Dual Channel Tube Program Equalizer based on the Pultec 1A3

The Retro Instruments 2A3 is a stereo, tube based, vintage emulating, passive equaliser. Designed around the industry standard Pultec EQ performance, the 2A3 adds HF boost frequencies in several new spots. Carefully implemented circuitry capture the classic sound of the original passive EQ units. These settings mean you can attenuate individual tracks to sit comfortably against each other, bring new life out of vocal parts and add distinction to stereo busses.

The 2A3 has a subsonic filter, which allows you to boost low frequencies without attenuating the subsonic energy below. The filter can be adjusted between 40 and 90Hz with a peaking response and has a sharp cut-off. The unit can run two channels in stereo, each channel independent or in series with each channel after the other for extended eq control.

Retro Instruments 2A3 Features and Specifications

  • Signal to noise ratio of greater than 76dB
  • Channel Separation greater than 70 dB
  • Frequency response is flat within 1 dB from 20 Hz-20,000 Hz
  • Harmonic Distortion is less than 1% from 20 Hz-20,000 Hz
  • Industry-standard Passive EQ with authentic feel, controls and equalization curves
  • Additional HF Boost Frequencies for more precise control
  • Easily recallable 100-position knob scales on boost and cut controls
  • A ganged interstage-coupled Subsonic High-Pass Filter provides Peaking LF Boosts with alternate tonal characteristics
  • Transformer Balanced and fully-floating 600 Ohm Input and Output to eliminate ground-induced hum and noise
  • LF Boost Settings of 20, 30, 60 and 100 Hz
  • Complementary LF Cut settings of 20, 30, 60 and 100 Hz
  • HF Boost Settings of 1.5 kHz, 3 kHz, 4 kHz, 5 kHz, 6 kHz, 8 kHz, 10 kHz, 12 kHz, 14 kHz and 16 kHz
  • Complementary HF Cut Settings of 5 kHz, 10 kHz and 20 kHz
  • Vintage Class AB tube amplification for unity-gain make-up
  • Equalization Bypass Switches
  • Size 2U Height: 19" wide x 3.5" tall x 9" deep
  • XLR input and output connections
  • IEC power connector
  • 115/230V 50-60 Hz Switchable AC Mains
  • Uses readily available 12AX7(2) and 12AU7(2) electron tubes
  • Tube substitutions are possible with internal unity gain calibration and jumper selectable 6 or 12 volt tube configuration
  • Design minimizes tube heat generation
  • High stability components used throughout
  • Steel Chassis built to last
  • Manufactured in the USA
  • Full factory support
Manufacturer Retro Instruments
SKU SRET2A3
Model Retro Instruments 2A3
GTIN N/A
Retro Instruments
Retro Instruments
Retro Instruments 2A3
Contact Us

Studiocare Professional Audio Ltd.

Unit 2, 56 Evans Road


Liverpool

L24 9PB


Phone
+44 (0) 151 707 4545
+44 (0) 845 345 8910


Opening Hours
Mon - Fri: 9:30 - 5:30
Sat - Sun: Closed
Help

Contact
How To Find Us
Terms & Conditions
Shipping
Newsletter
Returns Form
Repair Request
Studiocare on FacebookStudiocare on TwitterStudiocare on Google+” width=Studiocare on YoutubeStudiocare on Pintrest

Studiocare
© Copyright Studiocare Professional Audio Ltd. 2016