Currency:
T: 0151 707 4545

Moog Moogerfooger MF-107 FreqBox

THIS PRODUCT IS NO LONGER AVAILABLE.
Contact us to discuss sourcing this or similar products.
0151 236 7800 - sales@studiocare.com

£319.00 £265.83 (ex. vat)


Moog Moogerfooger MF-107 Modulated Oscillator Pedal

  • Moog Moogerfooger MF-107 Modulated Oscillator Pedal

The Moog MF-107 FreqBox is an audio modulated oscillator, capable of totally out-of-this-world, zany and freak sound mangling for all types of signals - guitars, synths, drum sounds, vocals or wind instruments, allowing you to enter previously unexplored sonic territory.

The Moog MF-107 FreqBox is different from other effects - the effected sound is not a processed version of your input signal, but the sound of the input signal modulating an internal oscillator (VCO) with continuously variable waveshape, and the capacity to modulate that Oscillator in four different ways. The VCO can be hard synced by the input signal, it can be frequency modulated (FM) by the input signal, its frequency can be modulated by an envelope follower which tracks the dynamics of the input signal and finally the Amplitude of the VCO also tracks the dynamics of the input signal.

Hard sync is a classic analog synthesis technique where the start of an oscillator's cycle can be reset by another. The oscillator being synced takes on the frequency characteristics of the other oscillator, and when its frequency is swept, it reinforces the harmonics of the fundamental frequency. In the case of the FreqBox, the input signal is used to reset the FreqBox's VCO.

FM is a technique used to get really rich sounds from simple waveforms. The type of FM used in the FreqBox is linear FM. Sounds range from gong or bell-like tones to sizzly sweeps.

The FreqBox, like all moogerfoogers, works with any instrument to line-level input. In addition to the panel controls there are control inputs for use with expression pedals or control voltages and control outputs for interconnecting moogerfoogers like you would a modular synth.

The FreqBox can provide some really unusual processing to all types of signals - guitars, synths, drum sounds, vocals or wind instruments allowing you to enter previously unexplored sonic territory.

Moog MF-107 FreqBox Features

  • Frequency: sets the frequency of the VCO.
  • Wave: Morphs the VCO waveform from Triangle to Sawtooth to Square to skinny pulse.
  • Sync On/Off: Enables/ Disables Hard sync of the VCO by the audio input signal.
  • Env. Amount: Sets the amount of modulation of the VCO frequency by the Envelope Follower.
  • FM Amount: Sets the amount of frequency modulation of the VCO by the audio input signal.
  • Mix: Sets the blend of input signal and VCO signal
  • Drive: Sets the input sensitivity and gain of the effect when active. Half to full drive amount adds overdrive.
  • Output level: Sets the output level of the effect when active.
  • Bypass Switch: Bypass LED is red when effect is off, and green when effect is on. The MF-107 uses a high quality buffered bypass - when in bypass, the input is disconnected from the effects electronics.
  • Audio Input: accepts instrument level to line level inputs.
  • Freq: Accepts EP-1 expression pedal, or -5 to +5V Control Voltage to set the frequency of the VCO. Input voltage is added to position of the front panel Frequency control.
  • Wave: Accepts EP-1 expression pedal, or -5 to +5V Control Voltage to set the waveform of the VCO. Input voltage is added to position of the front panel Wave control.
  • Env. Amt: Accepts EP-1 expression pedal, or 0 to +5V Control Voltage to set the amount of envelope follower modulation of the VCO frequency. Input voltage is added to position of the front panel Env. Amount control.
  • FM Amt: Accepts EP-1 expression pedal, or 0 to +5V Control Voltage to set the amount of frequency modulation of the VCO by the audio input. Input voltage is added to position of the front panel FM Amount control.
  • Mix: Accepts EP-1 expression pedal, or 0 to +5V Control Voltage to set the waveform of the VCO. Input voltage is added to position of the front panel Mix control.
  • Audio Out: Supplies the output signal.
  • Env Out: Outputs the unconditioned Envelope Follower Control Voltage signal.
  • Osc Out: Outputs the wave-shaped VCO signal as a +/-2.5V Control Voltage signal.
Manufacturer Moog
SKU SMOOMF107
Model Moog Moogerfooger MF-107
GTIN No
Moog
Moog
Moog Moogerfooger MF-107
Contact Us

Studiocare Professional Audio Ltd.

Unit 2, 56 Evans Road


Liverpool

L24 9PB


Phone
+44 (0) 151 707 4545
+44 (0) 845 345 8910


Opening Hours
Mon - Fri: 9:30 - 5:30
Sat - Sun: Closed
Help

Contact
How To Find Us
Terms & Conditions
Shipping
Newsletter
Returns Form
Repair Request
Studiocare on FacebookStudiocare on TwitterStudiocare on Google+” width=Studiocare on YoutubeStudiocare on Pintrest

Studiocare
© Copyright Studiocare Professional Audio Ltd. 2016