Currency:
T: 0151 707 4545

DPA Drum Pack Pro - 2 x 4011A, 2 x 2011C, 4 x 4099D, 1 x 4091 and Peli Case

£4,530.60 £3,775.50 (ex. vat)




DPA Drum Pack Pro

  • DPA Drum Pack Pro

DPA Drum Pack Pro - 9 Peice Drum Mic Kit 

The DPA Drum Pack Mic Kit is a 9 piece drum mic set that contains three 4099D tom mics, two 2011C compact condenser mics, two 4011A overhead condensers, one 4091 and all relevant clips and clamps.

The 4099D instrument mic is a great choice for toms, thanks the mic's clear performance and great off axis attenuation. The 2011C is a sensitive condenser that is designed to be used with high SPL, high frequency content that snare drums and hi hats produce. Finally, the included pair of 4011A cardioid condensers offfer colourless, clear pick-up of the entire kit when used as overheads and the miniature 4091 low-sensetivity condenser picks up the oomph of the kick. The package also comes in a heavy duty, tour ready Peli case for extra protection.

DPA Drum Pack Pro Included Mics

  • 1 x Snare mic: DPA d:dicate™ 2011C
  • 1 x Hi-hat mic: DPA d:dicate™ 2011C 
  • 2 x Overhead mics: DPA d:dicate™ 4011A 
  • 4 x Tom/Rack mics: DPA d:vote™ 4099D 
  • 1 x Kick drum mic: DPA d:screet™ 4091

DPA 4099D Tom Mic Specifications

  • Directional characteristics: Supercardioid
  • Principle of operation: Pressure gradient
  • Cartridge type: Pre-polarized condenser
  • Frequency range: 20 Hz to 20 kHz
  • Frequency range, ± 2 dB, 20 cm (7.9 in) distance: 80 Hz to 15 kHz with 2 dB soft boost at 10 to 12 kHz
  • Sensitivity, nominal ± 3 dB at 1 kHz: 2 mV/Pa; -54 dB re. 1 V/Pa
  • Equivalent noise level, A-weighted: Typ. 28 dB(A) re. 20 μPa (max. 31 dB(A))
  • S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): 66 dB(A)
  • Total Harmonic Distortion (THD): <1 % up to 123 dB SPL peak; <1 % up to 120 dB SPL RMS sine
  • Dynamic range: 95 dB
  • Max. SPL, peak before clipping: 152 dB
  • Output impedance: From MicroDot: 30 to 40 ohm; from DAD6001: 100 ohm
  • Cable drive capability: Up to 300 m (984 ft) with DAD6001 XLR adapter
  • Output balance principle: Signal balanced with DAD6001 XLR adapter
  • Common Mode Rejection Ratio (CMRR): > 60 dB from 50 Hz to 15 kHz with DAD6001 XLR adapter
  • Power supply (for full performance): Min. 5 V to max. 50 V through DPA adapter for wireless systems; 48 V phantom power +/- 4 V with DAD6001 XLR adapter
  • Current consumption: Typ. 1.5 mA (microphone). 3.5 mA with DAD6001 XLR adapter
  • Connector: MicroDot
  • Color: Black
  • Capsule diameter: 5.4 mm (0.2 in)
  • Microphone length: 45 mm (1.8 in)
  • Cable length: 1.8 m (6 ft)
  • Polarity: Positively increasing sound pressure produces positive-going voltage at MicroDot pin (and pin 2 on DAD6001 XLR adapter)
  • Temperature range: -40 °C to 45 °C (-40 °F to 113 °F)
  • Relative Humidity (RH): Up to 90%
  • Gooseneck length: 140 mm (5.5 in)

DPA 2011C Compact Condenser Specifications

  • Directional pattern: Cardioid
  • Principle of operation: Pressure gradient, with interference tube
  • Cartridge type: Pre-polarized condenser, Twin Diaphragm Capsule
  • Frequency range: 20 Hz to 20 kHz
  • Frequency range, ± 2 dB, at 30 cm: 50 Hz to 17 kHz with 3 dB soft boost at 12 kHz
  • Sensitivity, nominal, ± 2 dB at 1 kHz: 10 mV/Pa; -40 dB re. 1 V/Pa
  • Equivalent noise level, A-weighted: Typ. 20 dB(A) re. 20 µPa (max. 23 dB(A))
  • Equivalent noise level, ITU-R BS.468-4: Typ. 33 dB (max. 36 dB)
  • S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 74 dB(A)
  • Total Harmonic Distortion (THD) at 1 kHz: < 1 % up to 137 dB SPL peak
  • Minimum load impedance: 2 kohm
  • Dynamic range: Typ. 117 dB
  • Max. SPL, peak before clipping: 153 dB
  • Switchable attenuator: 0 dB / -20 dB
  • Output impedance: < 200 ohm
  • Cable drive capability: 100 m (328 ft)
  • Output balance principle: Impedance balancing with Active Drive
  • Common Mode Rejection Ratio (CMRR): > 60 dB
  • Power supply (for full specifications): 48 V Phantom power (± 4 V)
  • Current consumption: 2.8 mA
  • Connector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
  • Color: Matte black
  • Microphone weight: 164 g (5.8 oz)
  • Microphone diameter: 19 mm (0.75 in)
  • Microphone length: 198 mm (7.8 in)
  • Output voltage, RMS: > 5 V
  • Polarity: +V at Pin 2 for positive sound pressure
  • Temperature range: -40 °C to 45 °C (-40 °F to 113 °F)
  • Relative Humidity (RH): Up to 90% 

DPA 4011A Cardioid Condenser Specifications

  • Directional characteristics: Cardioid
  • Principle of operation: Pressure gradient
  • Cartridge type: Pre-polarized condenser
  • Frequency range: 20 Hz to 20 kHz
  • Frequency range, ±2 dB: 40 Hz to 20 kHz
  • Sensitivity, nominal ±2 dB at 1 kHz: 10 mV/Pa; -40 dB re. 1 V/Pa
  • Equivalent noise level, A-weighted, re. 20 µPa: Typ. 18 dB(A) re. 20 µPa (max. 20 dB)
  • Equivalent noise level, ITU-R BS.468-4: Typ. 25 dB (correct with the attenuator in 0 dB or -20 dB setting)
  • S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 76 dB(A)
  • Total Harmonic Distortion (THD): < 1 % up to 139 dB SPL peak
  • Minimum load impedance: 2 kohm
  • Dynamic range: Typ. 121 dB
  • Max. SPL, peak before clipping: 159 dB
  • Switchable attenuator: 0 dB / -20 dB
  • Output impedance: < 200 ohm
  • Cable drive capability: 100 m (328 ft)
  • Output balance principle: Impedance balancing with Active Drive
  • Common Mode Rejection Ratio (CMRR): > 60 dB
  • Power supply (for full specifications): 48 V Phantom power (± 4 V)
  • Current consumption: 2.8 mA
  • Connector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
  • Color: Matte black
  • Weight: 158 g (5.6 oz)
  • Microphone diameter: 19 mm (0.75 in)
  • Capsule diameter: 19 mm (0.75 in)
  • Length: 170 mm (6.7 in)
  • Output voltage, RMS: > 5 V
  • Polarity: +V at Pin 2 for positive sound pressure
  • Temperature range: -40 °C to 45 °C (14 °F to 113 °F)
  • Relative Humidity (RH): Up to 90 %
  • Matching tolerance: ± 1 dB
  • Phase deviation for kit: < 10°

DPA 4021 Low Sensetivity Condenser Specifications

  • Directional characteristics: Omnidirectional
  • Principle of operation: Pressure
  • Cartridge type: Pre-polarized condenser
  • Frequency range, ± 2 dB: 20 Hz – 20 kHz
  • Sensitivity, nominal, ± 3 dB at 1 kHz: 6 mV/Pa; -44.5 dB re. 1 V/Pa
  • Equivalent noise level, A-weighted: Typ. 26 dB(A) re. 20 µPa (max. 28 dB(A))
  • Equivalent noise level, ITU-R BS.468-4: Typ. 38 dB (max. 40 dB)
  • S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): 68 dB(A)
  • Total harmonic distortion (THD): < 1 % up to 123 dB SPL peak
  • Dynamic range: Typ. 97 dB
  • Max. SPL, peak before clipping: 144 dB
  • Output impedance: < 40 ohm
  • Cable drive capability: Up to 300 m (984 ft)
  • Output balance principle: Impedance balanced
  • Common Mode Rejection Ratio (CMRR): > 40 dB
  • Power supply: 48 V Phantom power ± 4 V
  • Current consumption: 2 mA
  • Connector: 3-pin XLR-M
  • Color: Black
  • Microphone weight: 38 g (1.34 oz)
  • Microphone diameter: 19 mm; at tip 6.7 mm (0.75 in; at tip: 0.26 in)
  • Capsule diameter: 5.4 mm (0.21 in)
  • Microphone length: 122 mm (4.8 in)
  • Polarity: Positively increasing sound pressure produces positive going voltage at pin 2
  • Temperature range: -40 °C to 45 °C (14 °F to 113 °F)
  • Relative humidity (RH): 90 %
Manufacturer DPA Microphones
SKU SDPADRUMPACKPRO
Model DPA Drum Pack Pro
GTIN N/A
DPA Microphones
DPA Microphones
DPA Drum Pack Pro
Contact Us

Studiocare Professional Audio Ltd.

Unit 2, 56 Evans Road


Liverpool

L24 9PB


Phone
+44 (0) 151 707 4545
+44 (0) 845 345 8910


Opening Hours
Mon - Fri: 9:30 - 5:30
Sat - Sun: Closed
Help

Contact
How To Find Us
Terms & Conditions
Shipping
Newsletter
Returns Form
Repair Request
Studiocare on FacebookStudiocare on TwitterStudiocare on Google+” width=Studiocare on YoutubeStudiocare on Pintrest

Studiocare
© Copyright Studiocare Professional Audio Ltd. 2016